Gate Repair in Burbank - On-Site in 60 Minutes, Fixed the Same Day

Gate Repair in Burbank, CA

Gate access control in Burbank usually means one of two jobs: adding keypad or phone entry to a 1940s ranch house gate in Magnolia Park, or wiring a video intercom into a high-cycle commercial slide gate on a studio lot. The Valley heat shortens motor life, the hard municipal water corrodes old hinges, and the Verdugo foothill grades demand gate hardware that flat-valley installers often spec wrong. Whether you need a keypad wired into an existing opener or a cracked iron rail welded before it snaps, we write the price down before any tool comes off the truck. Call (213) 566-1045 and a live person answers.

Call (213) 566-1045

Why Burbank Homes Are Different

Burbank is home to Warner Bros., Disney, and dozens of other studio campuses, so gate technicians here routinely work on heavy-duty, high-cycle slide and swing systems that run hundreds of cycles a day. That same commercial experience filters down into the residential side: the companies that survive in Burbank tend to carry both residential credentials and the documentation habits from studio lot work.

Most residential calls come from the post-WWII ranch and California bungalow neighborhoods around Magnolia Park and the flats south of Burbank Blvd. Those homes were built in the 1940s through the 1960s, and many still carry original wrought-iron driveway gates. The hardware is often 60-plus years old, pitted by hard municipal water, and now being retrofitted with automatic openers for the first time as the houses change hands. On the steep streets climbing into the Verdugo foothills, including Country Club Drive, we regularly see swing gates that were never properly counterbalanced for the grade. A gate that swings fine on a flat lot in Glendale binds and burns out its motor on a Burbank hillside. Summer temperatures over 100°F accelerate motor burnout and throw slide gate track alignment off as steel expands.

Our Main Burbank Services

Two services generate most of our Burbank calls. The other three have their own dedicated pages, linked below.

Gate Repair in Burbank

Gate Repair in Burbank covers what breaks most often out here: sagging hinges on 1950s iron gates, slide-gate rollers chewing through track after years of Valley heat cycling, and openers that quit mid-cycle. We diagnose on site, photograph what we find, and hand you a written price before we touch anything. For a gate that won’t open or a wheel that seized against the rail in the summer heat, this is the service.

Gate Installation in Burbank

Gate Installation in Burbank handles new driveway and pedestrian gates, including cantilever slide gates for hillside properties where a standard track would clog with debris and a swing gate would bind on the grade. We measure, spec the right hardware for the terrain, and give you a written scope with the price before ordering anything. No same-day promises on installs; this work is measured and scheduled.

Gate Motor & Opener in Burbank

Gate Motor & Opener in Burbank covers motor replacement, opener conversion from manual to automatic, and retrofitting swing-gate arms onto older gates in the Ranch District and hillside streets. We service nine major automation brands, so we match the motor to what’s already on the property rather than steering you toward a replacement. The Valley heat eats motors faster than coastal LA, which is why we also set travel limits and torque correctly the first time.

Before

After

Gate Access Control in Burbank

Gate access control in Burbank means wiring an entry system into a gate that’s already there. On a 1950s bungalow in the flats, that’s often a keypad or phone entry added to an existing iron driveway gate. On a studio lot or a hillside home with a long driveway, it’s more often a Gate Access Control video intercom or card reader tied into a high-cycle slide gate. The Burbank twist is the heat: exposed keypads and readers on south-facing gates bake in 100°F summers, so we use weather-sealed housings and position the electronics where the Valley sun won’t cook them by August. Adrian Vance built this company on commercial access-control documentation, and every Burbank visit, residential or studio, leaves with a wiring diagram and photo log under Clause 4 of the Haven Standard.

Keypad Entry

Signs you need it

You’re sharing gate codes that never get updated, and you want individual codes for family, housekeepers, or dog walkers.

What it costs in Burbank

Keypad entry added to an existing gate system in Burbank typically runs $450-$900 including wiring and programming.

How we do it

We mount a weather-sealed keypad, run the low-voltage wire to the opener’s control board, program the codes, and photograph the final wiring for your record.

Video Intercom

Signs you need it

You can’t see or talk to someone at the gate before deciding whether to open it, which matters on long Burbank driveways and studio-adjacent homes.

What it costs in Burbank

A residential video intercom in Burbank typically runs $1,200-$2,800 including the camera unit, indoor monitor, and wiring to the gate.

How we do it

We install the exterior camera at the gate, wire it to the indoor monitor, integrate call forwarding to your phone if requested, and test the full path before we call it done.

Phone Entry

Signs you need it

You want visitors to call your phone from the gate, with no app, no keypad code, and no separate monitor mounted on the wall.

What it costs in Burbank

Phone entry systems in Burbank typically run $800-$1,800 installed, depending on whether cellular or landline integration is needed.

How we do it

We install the cellular gateway at the gate, wire it into the opener’s trigger circuit, program your phone number, and test the ring-to-open path twice.

What Gate Access Control Costs in Burbank

Can you add a keypad to my existing gate motor in Burbank?

Yes, and it works with most major opener brands including LiftMaster, DoorKing, and FAAC. We match the keypad to your control board and wire it in without replacing the motor. Call (213) 566-1045 for a written price.

How long does gate access control installation take in Burbank?

Most keypad and phone entry installs finish in one visit of two to three hours. Video intercoms can take half a day if we’re trenching wire across a driveway or hillside lot. We give you a written time estimate before starting.

Gate Parts & Welding in Burbank

Gate parts and welding in Burbank usually means one of two scenarios: replacing hardware that has corroded over decades on a 1950s wrought-iron gate, or welding a crack that appeared where the Valley heat and the hillside grade have been working against the metal for years. The hard municipal water in Burbank accelerates rust on hinges, and the summer expansion cycles stress every weld on a south-facing gate. For any Gate Parts & Welding job, we match the part to the gate, photograph the failure before we cut, and hand you a written price before the torch comes out.

Hinge Replacement

Signs you need it

The gate drags on the ground, sags toward the latch post, or the hinge pin has worn an oval hole in the bracket.

What it costs in Burbank

Hinge replacement on a standard Burbank driveway gate typically runs $250-$600 per hinge, including the part, welding or bolting, and realignment.

How we do it

We support the gate, cut or unbolt the failed hinge, install the replacement, realign the gate in its opening, and photograph the new hinge position.

Custom Welding

Signs you need it

You see a crack in the frame, a broken picket, or a torn bracket, and the gate still works but won’t for much longer.

What it costs in Burbank

Custom welding repairs in Burbank typically run $180-$450 per repair point, depending on access, material thickness, and whether we need to remove the gate leaf.

How we do it

We grind the crack to clean metal, weld it, dress the joint, and repaint the area so the repair doesn’t read as a patch.

Rail Repair

Signs you need it

The slide gate jumps the rail, binds mid-travel, or shows visible bowing in the track between support posts.

What it costs in Burbank

Slide gate rail repair in Burbank typically runs $600-$1,200, including straightening or replacing the rail section, re-welding supports, and resetting the rollers.

How we do it

We straighten or replace the damaged rail, weld or bolt it back to the support, re-set the roller positions, and test the gate’s full travel.

What Gate Parts & Welding Costs in Burbank

Can you weld a gate without removing it from the hinges?

Often yes. We can weld most cracks in place with the gate supported and the surrounding area shielded. If access is tight or the gate is too far gone, we remove the leaf and weld it on the truck. You’ll know which before we start.

Do you source parts for old Burbank gates, or do I need to find them?

We source them. We carry common hinge brackets, roller kits, and weld plates in the truck, and we order brand-matched parts for older Viking, Elite, and DoorKing hardware the same day. The part number goes on your written invoice.

Brands We Service in Burbank

We work on whatever motor is already on your Burbank property. Viking, Ghost Controls, DoorKing, and Elite are four we see weekly, and we stock common parts for each locally so a repair doesn’t wait on a ground shipment. The full list is on our brands page.

Pricing for Gate Repair in Burbank, CA

Neighborhoods We Serve in Burbank

We work across Burbank, from the flats to the foothills. Response time for most repair calls in the city is under two hours, coordinated from our Los Angeles dispatch office.

• Magnolia Park
• Ranch District
• Verdugo foothills (Country Club Drive area)
• Downtown Burbank
• North Burbank / Burbank Blvd corridor

Service Area - Cities Near Burbank

We also serve the surrounding San Fernando Valley and Los Angeles neighborhoods. See North Hollywood, CA, Studio City, CA, Van Nuys, CA, and West Hollywood, CA for details on those service areas.

FAQs About Gate Repair in Burbank