Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in North Hollywood: What to Know First

We repair and install Linear gate motors and openers throughout North Hollywood, and most jobs are diagnosed same-day with the repair completed on the spot or within 48 hours once parts are in hand. Linear gate motor work in North Hollywood generally runs from $225 for a straightforward limit-switch reset to $1,400-$2,200 for a full motor replacement with new arms and brackets. Every price is written down and handed to you before we touch a tool. You’ll never get a call-back quote or an end-of-job surprise.

Call (213) 566-1045

If you own a Linear gate opener in North Hollywood and it’s grinding, stopping mid-travel, or the remote stopped working overnight, this page tells you what’s likely wrong, what it costs, and how we fix it. Call (213) 566-1045 and a live person answers, day or night.

How Linear Products Fail - and How We Fix Them

• Limit switch drift on the LS and LRA series. Linear swing and slide arms from the mid-2010s use mechanical limit cams that loosen with vibration. The gate over-travels, then slams into the open or closed stop. We see this constantly in North Hollywood, where daily opening cycles on driveways near Magnolia and Tujunga wear the cam screws loose. The fix is a physical reset and thread-lock on the cam screws, not a new board. About $185-$260.
• Capacitor failure on LDO and M3S slide motors. A Linear slide motor that hums but won’t move usually has a dead start capacitor. It’s a $35 part, but it mimics a failed motor and plenty of companies quote a full replacement. We test the capacitor before quoting anything. If the windings test clean, you pay for the capacitor and an hour of labor, not a $1,800 motor.
• Receiver lock-up after power events. The Linear ACT-34 and MCS series receivers occasionally freeze after brownouts or brief outages, which North Hollywood gets during Santa Ana season. The remote stops working, but the motor is fine. We re-flash the receiver and re-program remote codes in about 45 minutes. If the receiver board is genuinely dead, an aftermarket Linear-compatible unit runs $90-$160 installed.
• Worn carriage chain on slide operators. Linear slide openers from the SL and GSL lines run a chain-driven carriage that stretches over time. The gate starts jerking, then the chain jumps the sprocket. This is a known wear item. We measure chain stretch with a straightedge before replacing anything. If it’s within spec, we re-tension. If it’s beyond, we quote a new chain and sprocket kit, usually $320-$480 installed.
• Photo-eye misalignment on M3S and Smart Series swing arms. The infrared safety beam (the photo-eye that stops the gate if a car or kid is in the path) drifts on its bracket due to gate vibration. The gate refuses to close and the opener blinks a fault code. It’s a two-inch realignment, not a board failure. We photograph the final alignment for your record. Roughly $140-$190 for the call.

Our Linear Gate Motor & Opener Process

1. 1
   Call and describe what’s happening. You tell us the symptoms - grinding, no response, partial travel, fault lights. We bring the likely parts for your Linear model on the first trip.
2. 2
   On-site diagnosis. We meter the capacitor, test limit switch continuity, check chain tension, and photograph everything before touching anything.
3. 3
   Written price. You get a flat number on paper. It covers parts, labor, and cleanup. No ranges, no “we’ll see how it goes.” You approve it or we leave.
4. 4
   The repair. We use OEM Linear parts when the warranty or board compatibility calls for it, and quality aftermarket parts where they match or exceed OEM spec at a lower price. You’ll know which is going in and why.
5. 5
   Cycle testing. We run the gate through 20 full open-close cycles, verify the photo-eyes, test the force settings, and listen for abnormal motor load.
6. 6
   Documented handoff. You get a written record of the part numbers installed, the limit-switch positions, and photos of every adjustment. Under Clause 4 of the Haven Standard, evidence comes with every visit at no additional charge.

Before

After

What Linear Gate Motor & Opener Costs in North Hollywood

What moves the price: the model series (older LS and LDO units need more parts sourcing), whether the existing arm brackets are reusable or bent, and whether we’re pulling new low-voltage wire from the house to the gate. Every quote includes the part number, the labor, and the tax. Nothing is estimated verbally. Call (213) 566-1045 and we’ll price your Linear gate motor repair in writing before any work begins.

Why North Hollywood Homeowners Call Vance Gate Repair North Hollywood for Linear Work

We’ve seen what happens when a Linear gate gets “fixed” by someone who doesn’t know the brand - a homeowner near North Hollywood Park showed us a swing arm that had been mounted with the wrong bracket geometry, and the gate had warped the hinge plate over two months of stress. That doesn’t happen on our jobs. Adrian Vance has been running gate service calls in North Hollywood since moving the operation west, and he brings the commercial access-control documentation habit to every residential driveway: wiring notes, limit-set readings, photos of the final install.

If your Linear motor turns out to be beyond economical repair, we won’t steer you to one brand. We service nine automation lines - including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing - so the recommendation is based on your gate’s weight, your usage pattern, and your budget, not on what we happen to stock. And every job carries the 365-Day Done Right Promise: if the repair isn’t right, we make it right within a full year, no argument and no fee.

FAQs