Linear Gate Repair Nationwide

Linear Gate Repair in North Hollywood: What to Know First

Linear gate repair in North Hollywood typically runs between $185 and $480 for most board, limit-switch, and receiver faults, with same-day service available when we have the part on the truck. We service every Linear line still common in the Valley, including the APeX, MegaCode, and older AE series operators, as an independent Linear service provider. If your gate stopped responding to a remote, cycles halfway then reverses, or grinds without moving, call (213) 566-1045 and you’ll get a live person, a written price before work starts, and a photographed record of everything we find and fix.

Call (213) 566-1045

This page is for North Hollywood homeowners who own a Linear operator and want a repair that gets documented, not guessed at. Name what you found. Name what it costs. Leave the gate straight.

How Linear Products Fail - and How We Fix Them

• APeX series control boards losing receiver sync. The APeX line is solid mechanically but the receiver on the integrated board has a known drift issue after repeated power interruptions. Homeowners near Lankershim and Magnolia see this after summer brownouts: the gate works from the keypad but not the remote. We re-sync the receiver, check the antenna lead, and photograph the settings so a future reset takes two minutes instead of a service call.
• MegaCode receivers that stop accepting remotes one at a time. This usually isn’t the remote. It’s the receiver rolling-code memory filling or corrupting. Linear MegaCode receivers hold a finite number of transmitter slots, and if an old remote is deleted improperly the system can reject new programming. We clear and rebuild the transmitter table, test every remote on site, and hand you a written list of which remotes are enrolled.
• AE series limit switches drifting after years of hard stops. The older AE operators use mechanical limit cams, and on heavy gates they slip a few degrees each cycle. The symptom is a gate that closes then pops back open, or stops an inch short of the post. We reset the cams, torque the set screws to spec, and record the final limit positions in your job file. If the cams are worn past holding tolerance, we replace them with new OEM-equivalent parts and show you the old ones.
• Gearbox failures on Linear swing arms misdiagnosed as motor burnout. When a Linear swing-arm operator whines but doesn’t move the gate, the first assumption is a dead motor. In North Hollywood we see the gearbox output shaft shear or the worm gear strip more often than the motor winding fail. We open the unit, inspect the gear train, and replace only what’s actually broken. That’s the difference between a $300 gear set and an $1,100 motor replacement that wasn’t needed.
• Photo-eye faults triggered by Valley dust and alignment drift. Linear photo-eyes (the infrared beams that stop the gate when something crosses the path) are sensitive to the fine dust that settles on North Hollywood driveways. A misaligned pair by as little as two inches causes the gate to refuse to close, cycling back open every time. We clean the lenses, true the alignment, and verify the beam at both ends of travel. If a photocell has failed internally, we install a compatible replacement and test it with a physical obstruction, not just a meter reading.

Our Linear Gate Repair Process

1. 1
   You call (213) 566-1045. A live person answers, asks what the gate is doing or not doing, and schedules a dispatch. You get the technician’s name and photo before arrival.
2. 2
   Diagnosis in writing. The technician opens the operator, tests the board, limits, receiver, and safety devices, and writes down exactly what’s failed. You see the findings before you approve anything.
3. 3
   Written price, flat. Before any tool touches a fastener, you get a line-item price for parts and labor. That number doesn’t move unless you ask us to do additional work, and we’d write that up separately first.
4. 4
   The repair, with OEM or quality aftermarket parts depending on what makes sense. For Linear boards and receivers we use OEM or OEM-equivalent when it matters for compatibility. For gears, capacitors, and photo-eyes, we often use quality aftermarket parts that perform identically at half the cost. We tell you which we’re using and why, on every job.
5. 5
   Cycle testing and documentation. We run the gate through 10 full open-close cycles, check force settings, verify the photo-eyes and edge sensors, and photograph the finished work. You get a photo log and a written part number record before we leave.
6. 6
   The 365-Day Done Right Promise. If anything we touched fails within a year, we return and make it right. No argument, no fee, no expiration games.

Before

After

What Linear Gate Repair Costs in North Hollywood

Most Linear gate repairs in North Hollywood land between $185 and $480. Here’s what that looks like by the job:

• Receiver reprogramming or remote enrollment: $85-$150
• Limit switch reset or replacement: $140-$240
• Photo-eye realignment or replacement: $120-$220 per pair
• Control board replacement (APeX or MegaCode): $280-$480 depending on the board revision
• Gearbox or gear train repair on a swing arm: $260-$420
• Full operator replacement (motor and arm, existing post intact): $780-$1,350 installed

What moves the price: the age of the operator (AE-series parts are getting harder to source and cost more), whether the post and bracket are square, and whether the failure is electrical or mechanical. You’ll always know your number before we start. Estimates are free, and we’d rather hand you a written price than keep you guessing.

Why North Hollywood Homeowners Call Vance Gate Repair North Hollywood for Linear Work

We’re the gate company that writes things down. Adrian Vance started on commercial access-control sites back east in 2014, where every wire got labeled and every board setting got logged. That habit came with him to North Hollywood, and it’s why every Linear repair we do leaves behind a photographed record: the fault as found, the adjustment as made, the part number as installed. You’ll never pay a future technician to rediscover what we already fixed.

We also don’t steer you toward a replacement because the parts shelf says so. We service nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your Linear operator isn’t worth saving, we’ll tell you straight and give you options. But if it’s a $35 limit cam, we’ll replace the $35 limit cam. Under Clause 4 of our Haven Standard, every visit includes the documented photo record at no additional charge. Written price before work begins, every time, under Clause 1. And if a repair isn’t right, the 365-Day Done Right Promise means we’re back out to fix it at no charge.

FAQs